The following patch does the following:
Fixed bug with not all alarms enabled.
Added ability to read battery voltage
Select temperature sensor type at module load time.
Added setting for Inside Technologies 786LCD board to example config file
I also fixed what looked like a typo in the existing it87 section where
in6_min/max was set twice and in7 was not set. As commented I think
the equation for the negative voltages are wrong but without that motherboard
I can't verify.
With the 786LCD board sensors-detect reports a lm78 which doesn't
exist and a sis5595 which may be part of the SIS630 chip but doesn't
perform the monitoring. The it8705F/SIS950 which is on the board is
reported as a misdetect. I didn't know enough about the various chips
to figure out how to get correct detections.
David Gesswein
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1146 7894878c-1315-0410-8ee3-d5d059ff63e0
patch from Christian Zuckschwerdt:
Hi,
On Fri, 15 Jun 2001, Mark D. Studebaker wrote:
> I looked at the patch and I see there are separate
> /proc entries for the 9 and 12 bit outputs.
> Why not just make the 12 bit output the only output using "temp"??
> I don't understand the need for all the new /proc entries,
> except perhaps for debugging inside #ifdef DEBUG.
> Would you or Jan be willing to develop a patch that way?
> I'm all for increased accuracy as a standard feature - why not?
Ok. I rewrote the patch to support standard (9bit) and enhanced (12bit)
accuracy via the "temp" entry. The "raw" interface is also gone.
There are some quirks needed for the sensors app. It seems that
prog/sensors/chips.c fixes the output to %+3.1f
Thats not good for 12bit mode which gives you 2 decimals and therefor
wrong scaling.
Precision is .062 with 12bit (4 decimal bits) instead of .5 with 9bit (1
decimal bit). That way 2 decimals seem a natural choice.
On the other hand I see no obvious reason not to fix decimals to 1...
I'm lost there -- suggestions anyone?
Another problem is that 12bit is slow and laggy. I don't recommend making
it the default mode.
cu.
:
Christian
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1145 7894878c-1315-0410-8ee3-d5d059ff63e0
> - Update, if necessary, the version number of `sensors'
> (edit prog/sensors/main.c and change the VERSION define)
> `cvs diff -r Vx-y-z prog/sensors' is your friend.
It seems that VERSION is now defined to LM_VERSION, so I removed this line
from the checklist.
> - Update if necessary, the version number of libsensors
I did a `cvs diff -r V2-5-5'. Looking at it, I see no interface changes,
but I do see new functionality. So I updated the library minor version.
The library version is now 1.2.0.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1129 7894878c-1315-0410-8ee3-d5d059ff63e0
_sysctl_real
_register_entry
_proc_real
_detect
_deregister_entry
_chips_data
which were the global symbols renamed in i2c-proc.[ch] in the
i2c package.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1101 7894878c-1315-0410-8ee3-d5d059ff63e0
on both platforms). LM87 support is very far along, and should work
for a majority of users, but some minor tweaks are still on the to-do list.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@963 7894878c-1315-0410-8ee3-d5d059ff63e0
4 banks per memory chip. Add banks entry to libsensors and
use # of banks in calculation.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@839 7894878c-1315-0410-8ee3-d5d059ff63e0
This often-asked for, long-planned and somewhat-forgotten feature
makes it possible to tell libsensors-linked applications (like
the sensors program) that certain features should not be displayed.
This is very nice for things like unconnected temperature sensors
or fans.
Modifications to the library code, to the sensors program and to
the documentation and example sensors.conf file.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@676 7894878c-1315-0410-8ee3-d5d059ff63e0
Set DESTDIR if you want to install at some other place then where you
will run everything from.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@675 7894878c-1315-0410-8ee3-d5d059ff63e0
* Removed several superfluous (struct i2c_client *) casts (they were left
from the time we had separate structs for smbus and isa)
* Removed the internal lists of registered clients
They have not been used for quite some time now, took memory space,
and limited the maximum number of clients that could be registered.
Also removed two small Makefile errors - I am happy I caught them before
the next release!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@582 7894878c-1315-0410-8ee3-d5d059ff63e0
* gl518sm document simplified for rev 0x00 & 0x80
* gl518sm & gl520sm libsensors interface updates
BTW: Revision is no longer part of the name, so old sensors.conf
will not work at all with gl518sm.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@511 7894878c-1315-0410-8ee3-d5d059ff63e0
* The library can now read GL518SM revision 0x00 voltages (in the worst case,
it will read zeros if the module was not inserted with readall=1)
* The readall parameter is now documented through MODULE_PARM_DESC
* Note my remarks in the TODO file
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@403 7894878c-1315-0410-8ee3-d5d059ff63e0
* Readings for the ADM9240 are now updated every 0.5 seconds; for the
DS1780, every 2.0 seconds.
* I still think it likely that voltage readings will be far-off in the
current implementation
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@401 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker