as the BIOS is supposed to set them up properly. This information makes it
easier to find out which temperature channel corresponds to the CPU.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4456 7894878c-1315-0410-8ee3-d5d059ff63e0
based on preliminary work by Yuan My (Winbond). Thanks to Bernardo Motta
at Observit for providing the hardware that made it possible.
Note that support for the W83627DHG isn't included, but it could easily be
added later is anyone needs it.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4447 7894878c-1315-0410-8ee3-d5d059ff63e0
be available in Linux kernel 2.6.23. Binary compatibility is guaranteed,
source code compatibility isn't, but the incompatibility will be
spotted quickly as the prototype of the helper function
i2c_smbus_read_i2c_block_data() changed. The only problem would be if
a program is calling i2c_smbus_access() directly. Hopefully this should
be a rare case. The py-smbus binding code is in this case and will be
adjusted soon.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4417 7894878c-1315-0410-8ee3-d5d059ff63e0
The i2c-ali1563 initialization looks quite broken to me:
* If the I/O space isn't enabled, we forcibly set 3 bits in
the PCI configuration space instead of just the one enabling
the I/O space.
* After that we pretend to check if the write worked, but we
don't actually read the new value from the register.
* It's probably not a good idea to enable the I/O space if no
base address has been set.
So I propose the following changes to that part of the driver:
* Merge ali1563_enable() into ali1563_setup().
* Check the base address before the I/O space enabled bit.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4324 7894878c-1315-0410-8ee3-d5d059ff63e0
* Add an explicit mask when writing the low byte of a word.
* Use I2C_SMBUS_BLOCK_MAX instead of hardcoding 32.
* Use boolean not instead of bitwise not for bit tests, it's clearer.
* Return proper error values rather than -1.
* Fix a race on device registration, initialization should be done
before the bus is registered.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4318 7894878c-1315-0410-8ee3-d5d059ff63e0
The lowest 3 bits are ignored, and the chip decodes all 8 addresses,
not only the 2 it needs. This is a backport from Linux 2.6.20.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4263 7894878c-1315-0410-8ee3-d5d059ff63e0
input order to match the Linux 2.6 driver.
libsensors: Change vt1211 temp3-7 magnitude from 1 to 3.
sensors.conf.eg: Adjust the vt1211 section to match the new driver
interface.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4168 7894878c-1315-0410-8ee3-d5d059ff63e0
Also update to display the (beep) properly due to the fact that the
w83791d beep enable mask is different than the alarm mask.
Patch from Sven Anders and Charles Spirakis.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4096 7894878c-1315-0410-8ee3-d5d059ff63e0
* Fix self file name reference.
* i801_setup can be marked __devinit.
* Drop useless error local variable and label in i801_setup.
* Use symbolic names for SMBHSTCFG bits.
* Transmit the error code returned by i801_setup instead of forcing it
to an arbitrary value.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4061 7894878c-1315-0410-8ee3-d5d059ff63e0
Remove the PCI function number check when probing devices.
This check is redundant, each function has a separate PCI device
ID, so checking for that ID is sufficient.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4060 7894878c-1315-0410-8ee3-d5d059ff63e0
Two of the three poll loops have the poll and sleep swapped,
causing an extra sleep to occur after the polled condition is
fulfilled. In practice, this doubles the amount of sleep time for
every block transaction.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4059 7894878c-1315-0410-8ee3-d5d059ff63e0
430) and nForce4 MCP55 to the i2c-nforce2 driver. Some code changes
were required because the base I/O address registers have changed in
these versions. Standard BARs are now being used, while the original
nForce2 chips used non-standard ones. (2.6 backport)
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4054 7894878c-1315-0410-8ee3-d5d059ff63e0
refuse to load. Hopefully this will make it clearer for users, which
were often wondering why their destop or server systems were detected
as laptops.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4053 7894878c-1315-0410-8ee3-d5d059ff63e0
Jean Delvare