This adds a config file for the MSI X370 SLI Plus. Similiar models may
work with derived configurations.
[olysonek: fixed up 'compute in3' statement, fixed up whitespace,
reformatted description]
Apparently, Gigabyte uses a 8kOhm and a 2.7kOhm resistor for the
voltage divider (both are commercially available SMD resistors). It
matches my BIOS reading.
Applied from PR
https://github.com/lm-sensors/lm-sensors/pull/203
[olysonek: squashed commits, updated description]
This motherboard supports one external temperature sensor. When there isn't
anything connected it shows very low values (e.g. -55C in my case).
Signed-off-by: Karol Grudziński <krlgrudzinski@gmail.com>
According to:
"Quad-Core Intel® Xeon(R) Processor 5400 Series Electrical Specifications"
(table 2-12), FSB termination voltage of the CPUs (VTT) is 1.1V +/-5%.
Initial configuration set it to 1.2V - fix that.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add configuration for Supermicro X7DCL motherboard.
Based on slightly modified setup of X7DBE from this repo.
Runtime tested on X7DCL-3 rev. 1.1a
So far there is only support for onboard sensors,
no support for PSU failure yet, nor external PMBus sensors.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Input routing and scaling for this board was read from schematic of a
similar MSI MS-7B00 (B350 Gaming Pro Carbon) board.
temp5 on the MS-7B00 schematic is a thermistor under the B350 chip itself.
However, on my MS-7A34 board the reading is stuck at 23°C.
Judging from MS-7A34 board sensor readings that other people had posted
online the sensor seems to work properly for them, so I have left it
enabled.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Input routing and scaling for this board was read from its schematic,
verified on a real specimen.
This config is likely also valid for other members of GA-F2A88XM-x family,
as differences between them seem pretty minor.
It might also be valid for GA-F2A85XM-HD3 board considering that
GA-F2A88XM-HD3 schematic has the former board name as title in many places.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Values as per nuvoton nct6779D datasheetSection 8.5 Analog Inputs (Page 54,55).
Is based on nct6779 which uses a 2.048V input range, all inputs above that are scaled using a voltage divider.
Specific inputs like the ADC, AVCC, VBAT, 3VSB and 3VCC utilize an integrated voltage divider.
Signed-off-by: Rigo Reddig <rigo.reddig@gmail.com>
Changes refer to issue #88. This change is backward compatible and is only a suggestion, a reference how the dmi and other information could be simply added into the config file for a board.
This is a bulk recovery of the sensor configs found at
https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations
The config sections themselves are unaltered, but I've selectively added
some, but not all of the extra info around them. Anywhere there's been
extra info added, it should be in comments at the top of the config,
followed by a double newline to indicate the separation. Attribution has
been retained where possible, but links to the mailing list are hosed,
so goto the above archive.org link to check if a config has extra origin
notes.
[groeck: reformatted description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is a bulk recovery of the sensor configs found at
https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations
The config sections themselves are unaltered, but I've selectively added
some, but not all of the extra info around them. Anywhere there's been
extra info added, it should be in comments at the top of the config,
followed by a double newline to indicate the separation. Attribution has
been retained where possible, but links to the mailing list are hosed,
so goto the above archive.org link to check if a config has extra origin
notes.
[groeck: reformatted description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Compared with values in EFI/BIOS factors should be pretty precise.
A Vcore in not specified in the CPU data sheet, therefore
these alarm values are pure guess.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
KonomiKitten