This was broken by 2.6.0 because
2.6.0 didn't reset the fan clock setting at startup.
Therefore the AS_FAN_* macros were no longer needed to specially
correct the fan speed. So remove the special handling and the
AS_FAN_* macros and things should work now.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1135 7894878c-1315-0410-8ee3-d5d059ff63e0
were copied to i2c.h in the i2c package).
No harm was done because i2c-isa.h is still in our package, and
it87 is not included in mkpatch yet.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1132 7894878c-1315-0410-8ee3-d5d059ff63e0
Alpha architecture. I've made compilation contingent on
the machine being an Alpha because the driver needs kernel
include files that are in <asm-alpha>, not <asm>, unless
you are set up as an Alpha.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1109 7894878c-1315-0410-8ee3-d5d059ff63e0
_sysctl_real
_register_entry
_proc_real
_detect
_deregister_entry
_chips_data
which were the global symbols renamed in i2c-proc.[ch] in the
i2c package.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1101 7894878c-1315-0410-8ee3-d5d059ff63e0
which ensures i2c Bus is tristated correctly. It isn't clear from
the datasheet if the 586's GPIO pins are open drain or not,
but if they aren't, then the driver was driving the pins high
rather than letting them get pulled high as the spec requires.
This is corrected by toggling the direction rather than the
data register to control the bus.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1093 7894878c-1315-0410-8ee3-d5d059ff63e0
Also automatically enable ACPI if it was disabled.
Forcing address doesn't work on my test system, but hey,
at least I tried to test it...
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1077 7894878c-1315-0410-8ee3-d5d059ff63e0
to force_addr. It is now consistent with the bus PCI adapters
that support base address setting (piix4, i801, viapro).
Other benefit is that via686a_find can now return -ENODEV,
and module will fail to load when base address is not set and
parameter is not used.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1073 7894878c-1315-0410-8ee3-d5d059ff63e0
The temperature registers are in different places for the two
versions. Both versions unfortunately have the same PCI ID.
Apparently the temperature conversion formulas are different
for the two versions. Neither is yet implemented in the driver.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1070 7894878c-1315-0410-8ee3-d5d059ff63e0
in a different place than the LM78, which this driver was copied from,
so temp was completely broken.
Temp shares a pin and registers with in4; add in4 support, recognize
chip configuration and act accordingly.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1067 7894878c-1315-0410-8ee3-d5d059ff63e0
that are configurable as we will count on the BIOS to configure
the chip correctly. This will likely change fan and temperature
readings for some users.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1039 7894878c-1315-0410-8ee3-d5d059ff63e0
These select fan type (2 or 3 wire) as well as temp sensor type
(thermistor or diode) and temperature vs. voltage sensing for
two pins. This should help those on various Tyan mobos.
Driver used to reset the chip and then program a fixed setting which
worked for the Tyan S1824D board but not for Tyan 2510.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1030 7894878c-1315-0410-8ee3-d5d059ff63e0
to match what mkpatch patches in patched kernel.
Affected only kernel patches; standalone build was fine.
Ticket # 492.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1026 7894878c-1315-0410-8ee3-d5d059ff63e0
Leave the files there for now.
Remove old installed sensors.o in kernel/Module.mk.
sensors.c was moved to i2c-proc.c in the i2c package.
i2c-isa.h was appended to i2c.h in the i2c package.
Delete all but the SYSCTL and ALARMS definitions in sensors.h,
as the rest of the file was moved to i2c-proc.h in the i2c package.
Remove #include "i2c-isa.h" lines in all chip drivers and
in bus driver i2c-isa.c.
This all probably breaks mkpatch.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1015 7894878c-1315-0410-8ee3-d5d059ff63e0
address and program the base address in the 686a.
This is NOT a PCI force; the 3057 device must
be present in lspci.
Should work for Asus A7V/K7V boards which don't set the
base address (because they also have a as99127f on them!??).
Some rough edges remain, because
via686a_find() does not know there is a force; that only
is apparent to via686a_detect().
Notably, the driver will stay loaded even if the address is
uninitialized and there is no force; also, the driver complains
that a force is needed even when you give it one.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@999 7894878c-1315-0410-8ee3-d5d059ff63e0
to mkpatch in 2.5.5. Also add mtp008 and ds1621 init calls in anticipation
of them being added. Fix typos adm9024->adm9240.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@997 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker