when encountering a long list of unsupported chips.
All these chips have the same 1039/0008 ID as the 5595 but are
incompatible.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1150 7894878c-1315-0410-8ee3-d5d059ff63e0
The following patch does the following:
Fixed bug with not all alarms enabled.
Added ability to read battery voltage
Select temperature sensor type at module load time.
Added setting for Inside Technologies 786LCD board to example config file
I also fixed what looked like a typo in the existing it87 section where
in6_min/max was set twice and in7 was not set. As commented I think
the equation for the negative voltages are wrong but without that motherboard
I can't verify.
With the 786LCD board sensors-detect reports a lm78 which doesn't
exist and a sis5595 which may be part of the SIS630 chip but doesn't
perform the monitoring. The it8705F/SIS950 which is on the board is
reported as a misdetect. I didn't know enough about the various chips
to figure out how to get correct detections.
David Gesswein
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1146 7894878c-1315-0410-8ee3-d5d059ff63e0
patch from Christian Zuckschwerdt:
Hi,
On Fri, 15 Jun 2001, Mark D. Studebaker wrote:
> I looked at the patch and I see there are separate
> /proc entries for the 9 and 12 bit outputs.
> Why not just make the 12 bit output the only output using "temp"??
> I don't understand the need for all the new /proc entries,
> except perhaps for debugging inside #ifdef DEBUG.
> Would you or Jan be willing to develop a patch that way?
> I'm all for increased accuracy as a standard feature - why not?
Ok. I rewrote the patch to support standard (9bit) and enhanced (12bit)
accuracy via the "temp" entry. The "raw" interface is also gone.
There are some quirks needed for the sensors app. It seems that
prog/sensors/chips.c fixes the output to %+3.1f
Thats not good for 12bit mode which gives you 2 decimals and therefor
wrong scaling.
Precision is .062 with 12bit (4 decimal bits) instead of .5 with 9bit (1
decimal bit). That way 2 decimals seem a natural choice.
On the other hand I see no obvious reason not to fix decimals to 1...
I'm lost there -- suggestions anyone?
Another problem is that 12bit is slow and laggy. I don't recommend making
it the default mode.
cu.
:
Christian
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1145 7894878c-1315-0410-8ee3-d5d059ff63e0
This was broken by 2.6.0 because
2.6.0 didn't reset the fan clock setting at startup.
Therefore the AS_FAN_* macros were no longer needed to specially
correct the fan speed. So remove the special handling and the
AS_FAN_* macros and things should work now.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1135 7894878c-1315-0410-8ee3-d5d059ff63e0
were copied to i2c.h in the i2c package).
No harm was done because i2c-isa.h is still in our package, and
it87 is not included in mkpatch yet.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1132 7894878c-1315-0410-8ee3-d5d059ff63e0
Alpha architecture. I've made compilation contingent on
the machine being an Alpha because the driver needs kernel
include files that are in <asm-alpha>, not <asm>, unless
you are set up as an Alpha.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1109 7894878c-1315-0410-8ee3-d5d059ff63e0
_sysctl_real
_register_entry
_proc_real
_detect
_deregister_entry
_chips_data
which were the global symbols renamed in i2c-proc.[ch] in the
i2c package.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1101 7894878c-1315-0410-8ee3-d5d059ff63e0
which ensures i2c Bus is tristated correctly. It isn't clear from
the datasheet if the 586's GPIO pins are open drain or not,
but if they aren't, then the driver was driving the pins high
rather than letting them get pulled high as the spec requires.
This is corrected by toggling the direction rather than the
data register to control the bus.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1093 7894878c-1315-0410-8ee3-d5d059ff63e0
Also automatically enable ACPI if it was disabled.
Forcing address doesn't work on my test system, but hey,
at least I tried to test it...
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1077 7894878c-1315-0410-8ee3-d5d059ff63e0
to force_addr. It is now consistent with the bus PCI adapters
that support base address setting (piix4, i801, viapro).
Other benefit is that via686a_find can now return -ENODEV,
and module will fail to load when base address is not set and
parameter is not used.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1073 7894878c-1315-0410-8ee3-d5d059ff63e0
The temperature registers are in different places for the two
versions. Both versions unfortunately have the same PCI ID.
Apparently the temperature conversion formulas are different
for the two versions. Neither is yet implemented in the driver.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1070 7894878c-1315-0410-8ee3-d5d059ff63e0
in a different place than the LM78, which this driver was copied from,
so temp was completely broken.
Temp shares a pin and registers with in4; add in4 support, recognize
chip configuration and act accordingly.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1067 7894878c-1315-0410-8ee3-d5d059ff63e0
that are configurable as we will count on the BIOS to configure
the chip correctly. This will likely change fan and temperature
readings for some users.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1039 7894878c-1315-0410-8ee3-d5d059ff63e0
These select fan type (2 or 3 wire) as well as temp sensor type
(thermistor or diode) and temperature vs. voltage sensing for
two pins. This should help those on various Tyan mobos.
Driver used to reset the chip and then program a fixed setting which
worked for the Tyan S1824D board but not for Tyan 2510.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1030 7894878c-1315-0410-8ee3-d5d059ff63e0
to match what mkpatch patches in patched kernel.
Affected only kernel patches; standalone build was fine.
Ticket # 492.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1026 7894878c-1315-0410-8ee3-d5d059ff63e0
Leave the files there for now.
Remove old installed sensors.o in kernel/Module.mk.
sensors.c was moved to i2c-proc.c in the i2c package.
i2c-isa.h was appended to i2c.h in the i2c package.
Delete all but the SYSCTL and ALARMS definitions in sensors.h,
as the rest of the file was moved to i2c-proc.h in the i2c package.
Remove #include "i2c-isa.h" lines in all chip drivers and
in bus driver i2c-isa.c.
This all probably breaks mkpatch.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1015 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker