'supported' table. i2c adapter name and io region will
always be piix4 now - too hard to do 5 different names.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1188 7894878c-1315-0410-8ee3-d5d059ff63e0
The following patch does the following:
Fixed bug with not all alarms enabled.
Added ability to read battery voltage
Select temperature sensor type at module load time.
Added setting for Inside Technologies 786LCD board to example config file
I also fixed what looked like a typo in the existing it87 section where
in6_min/max was set twice and in7 was not set. As commented I think
the equation for the negative voltages are wrong but without that motherboard
I can't verify.
With the 786LCD board sensors-detect reports a lm78 which doesn't
exist and a sis5595 which may be part of the SIS630 chip but doesn't
perform the monitoring. The it8705F/SIS950 which is on the board is
reported as a misdetect. I didn't know enough about the various chips
to figure out how to get correct detections.
David Gesswein
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1146 7894878c-1315-0410-8ee3-d5d059ff63e0
patch from Christian Zuckschwerdt:
Hi,
On Fri, 15 Jun 2001, Mark D. Studebaker wrote:
> I looked at the patch and I see there are separate
> /proc entries for the 9 and 12 bit outputs.
> Why not just make the 12 bit output the only output using "temp"??
> I don't understand the need for all the new /proc entries,
> except perhaps for debugging inside #ifdef DEBUG.
> Would you or Jan be willing to develop a patch that way?
> I'm all for increased accuracy as a standard feature - why not?
Ok. I rewrote the patch to support standard (9bit) and enhanced (12bit)
accuracy via the "temp" entry. The "raw" interface is also gone.
There are some quirks needed for the sensors app. It seems that
prog/sensors/chips.c fixes the output to %+3.1f
Thats not good for 12bit mode which gives you 2 decimals and therefor
wrong scaling.
Precision is .062 with 12bit (4 decimal bits) instead of .5 with 9bit (1
decimal bit). That way 2 decimals seem a natural choice.
On the other hand I see no obvious reason not to fix decimals to 1...
I'm lost there -- suggestions anyone?
Another problem is that 12bit is slow and laggy. I don't recommend making
it the default mode.
cu.
:
Christian
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1145 7894878c-1315-0410-8ee3-d5d059ff63e0
> - Update, if necessary, the version number of `sensors'
> (edit prog/sensors/main.c and change the VERSION define)
> `cvs diff -r Vx-y-z prog/sensors' is your friend.
It seems that VERSION is now defined to LM_VERSION, so I removed this line
from the checklist.
> - Update if necessary, the version number of libsensors
I did a `cvs diff -r V2-5-5'. Looking at it, I see no interface changes,
but I do see new functionality. So I updated the library minor version.
The library version is now 1.2.0.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1129 7894878c-1315-0410-8ee3-d5d059ff63e0
Alpha architecture. I've made compilation contingent on
the machine being an Alpha because the driver needs kernel
include files that are in <asm-alpha>, not <asm>, unless
you are set up as an Alpha.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1109 7894878c-1315-0410-8ee3-d5d059ff63e0
instructions on how to use the BT869 driver with a PAL TV, an X windows
server, and kernel 2.4.4.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1083 7894878c-1315-0410-8ee3-d5d059ff63e0
to force_addr. It is now consistent with the bus PCI adapters
that support base address setting (piix4, i801, viapro).
Other benefit is that via686a_find can now return -ENODEV,
and module will fail to load when base address is not set and
parameter is not used.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1073 7894878c-1315-0410-8ee3-d5d059ff63e0
The temperature registers are in different places for the two
versions. Both versions unfortunately have the same PCI ID.
Apparently the temperature conversion formulas are different
for the two versions. Neither is yet implemented in the driver.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1070 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker