The following patch does the following:
Fixed bug with not all alarms enabled.
Added ability to read battery voltage
Select temperature sensor type at module load time.
Added setting for Inside Technologies 786LCD board to example config file
I also fixed what looked like a typo in the existing it87 section where
in6_min/max was set twice and in7 was not set. As commented I think
the equation for the negative voltages are wrong but without that motherboard
I can't verify.
With the 786LCD board sensors-detect reports a lm78 which doesn't
exist and a sis5595 which may be part of the SIS630 chip but doesn't
perform the monitoring. The it8705F/SIS950 which is on the board is
reported as a misdetect. I didn't know enough about the various chips
to figure out how to get correct detections.
David Gesswein
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1146 7894878c-1315-0410-8ee3-d5d059ff63e0
This often-asked for, long-planned and somewhat-forgotten feature
makes it possible to tell libsensors-linked applications (like
the sensors program) that certain features should not be displayed.
This is very nice for things like unconnected temperature sensors
or fans.
Modifications to the library code, to the sensors program and to
the documentation and example sensors.conf file.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@676 7894878c-1315-0410-8ee3-d5d059ff63e0
Set DESTDIR if you want to install at some other place then where you
will run everything from.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@675 7894878c-1315-0410-8ee3-d5d059ff63e0
* GL518 & GL520: setting fan{1,2}_min 0 masks alarm & beep
* GL518SM rev 0x00 : Run iteration code in kernel thread
Every run of "sensors" now reports results of the previous
iteration run, and triggers a new one.
* GL520: Reads all inputs now
* GL520: Select between Temp2 or -12V input.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@520 7894878c-1315-0410-8ee3-d5d059ff63e0
* gl518sm document simplified for rev 0x00 & 0x80
* gl518sm & gl520sm libsensors interface updates
BTW: Revision is no longer part of the name, so old sensors.conf
will not work at all with gl518sm.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@511 7894878c-1315-0410-8ee3-d5d059ff63e0
Now prints out what kind of sensor it is.
Also separated alarms for temp2 and temp3 for 782d/783s (they are
a single bit for 781d).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@400 7894878c-1315-0410-8ee3-d5d059ff63e0
I've reviewed and applied the patch, but I would like some others to review
these commits too, to be safe.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@327 7894878c-1315-0410-8ee3-d5d059ff63e0
Renamed sensors entry from "SiS 5595 Sensor-*" to "sis5595-*"
Added this name in sensors.conf.eg to use lm78 names for inputs.
Small related document updates.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@199 7894878c-1315-0410-8ee3-d5d059ff63e0
* Better VDD internal computation, as described in the data sheet;
* Fixed the config file to reflect the above change;
* The library read the wrong file to get its gl518sm alarm data.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@150 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker